| Isolation mechanism | Transfers digital signals across an insulation barrier using capacitive coupling. | Transfers digital signals across an insulation barrier using magnetic coupling, commonly through integrated transformer structures. | Transfers signals using light emitted by an LED and detected across an optical barrier. | Confirm that the isolation technology and package construction suit the required safety classification and system architecture. |
| Data rate | Available in low-speed and high-speed variants; maximum rate is specific to the device. | Available in low-speed and high-speed variants; maximum rate is specific to the device. | Ranges from relatively low-speed devices to high-speed types; performance depends strongly on the optocoupler design and circuit. | Compare the guaranteed maximum data rate with the protocol rate, required margin, and worst-case operating conditions. |
| Propagation delay and timing | Delay, pulse-width distortion, and channel-to-channel matching vary by device and data rate. | Delay, pulse-width distortion, and channel-to-channel matching vary by device and data rate. | Delay and pulse-width distortion vary by device and can be affected by LED drive and output circuitry. | Check maximum propagation delay, pulse-width distortion, skew, and timing over the full temperature range. |
| Common-mode transient immunity (CMTI) | Specified by the individual device; fast common-mode transitions can challenge signal integrity across any isolation barrier. | Specified by the individual device; performance depends on the barrier design and test conditions. | Specified by the individual device and circuit; layout and parasitic capacitance can affect transient performance. | Compare the guaranteed CMTI rating and test conditions with expected switching transients in the application. |
| Isolation ratings | Working voltage, withstand voltage, creepage, and clearance are product- and package-specific. | Working voltage, withstand voltage, creepage, and clearance are product- and package-specific. | Working voltage, withstand voltage, creepage, and clearance are product- and package-specific. | Do not infer safety performance from the coupling method alone. Verify the exact ratings and applicable approvals in the datasheet. |
| Power and interface requirements | Usually requires supplies on both sides of the barrier; consumption depends on data rate, channel count, and device design. | Usually requires supplies on both sides of the barrier; consumption depends on data rate, channel count, and device design. | Requires LED drive current and an output-side circuit; total power depends on the LED current and output configuration. | Compare total power at realistic switching activity, supply voltage, and temperature—not just a headline typical value. |
| Lifetime and aging | Does not rely on an LED transfer path; operating life is still limited by device ratings and environmental conditions. | Does not rely on an LED transfer path; operating life is still limited by device ratings and environmental conditions. | LED light output can decrease with time and operating stress, which may affect transfer performance. | For long-life equipment, review lifetime data, operating temperature, stress conditions, and any required design margin. |
| Channel options | Single- and multi-channel configurations are available; channel direction and isolation arrangement vary by device. | Single- and multi-channel configurations are available; channel direction and isolation arrangement vary by device. | Single- and multi-channel packages are available; channel count and direction depend on the package. | Match channel count, direction, logic polarity, and package pinout to the design to reduce extra circuitry. |
| Fail-safe behavior | Default output state during input loss or power loss is device-specific. | Default output state during input loss or power loss is device-specific. | Output behavior depends on the optocoupler output type and external circuit. | Verify output state during startup, shutdown, and loss of either-side power; choose a defined safe state where required. |
| Industrial environment | Temperature range, package robustness, and electrical limits vary by device. | Temperature range, package robustness, and electrical limits vary by device; assess magnetic-field exposure if relevant. | Temperature range and package robustness vary by device; account for LED aging and the surrounding circuit. | Check the specified temperature range, humidity and pollution assumptions, PCB layout rules, and expected electrical noise. |
| Typical application fit | Useful for compact, integrated digital isolation where the device’s ratings and transient performance meet the design needs. | Useful for integrated digital isolation where the device’s ratings, transient performance, and field environment are suitable. | Useful where optical isolation is preferred or an existing design uses optocouplers and their operating characteristics are acceptable. | There is no universally best option: select by verified safety ratings, timing, CMTI, power, lifetime, environment, and total system cost. |