| 1. Map the noise sources | Variable-speed drives, servo drives, switching power supplies, relay coils, contactors, and arc-producing equipment. | PLC inputs, analog sensors, encoder circuits, communication interfaces, and weighing or measurement systems. | Faults or unstable readings appear when a particular machine starts, stops, or changes operating speed. | Record when symptoms occur; compare them with machine events. Inspect cable routes and use suitable current or field probes to locate noisy circuits. | Separate noisy power wiring from control and signal wiring. Confirm bonding and cable-screen connections before adding filters. |
| 2. Check conducted interference paths | Noise coupled onto power, signal, or grounding conductors by switching loads, drives, or shared supplies. | Equipment sharing the same supply, long sensor loops, and devices connected to common control or communication wiring. | Several devices misbehave together, or a problem changes when a load is switched or an electrical connection is rerouted. | Inspect supply and signal wiring, grounding topology, and cable shields. For formal investigations, conducted-emissions measurements commonly examine the 150 kHz–30 MHz range, subject to the applicable test standard. | Review circuit separation and bonding; consider a correctly rated line filter or signal isolation where measurements show it is appropriate. |
| 3. Look for radiated coupling | Fast-switching power electronics, high-current conductors, radio transmitters, and poorly contained electrical arcs. | Unshielded sensor wiring, high-impedance inputs, wireless or radio equipment, and devices with exposed or long interconnects. | Interference depends on distance, enclosure doors, cable position, or the operating state of a nearby source. | Compare behavior at different distances and cable positions. Use a near-field probe or an appropriate EMC test setup to locate emissions; test ranges depend on the product standard. | Reduce loop area, improve enclosure bonding, and route sensitive cables away from high-current or fast-switching circuits. |
| 4. Assess susceptibility by function | Electrostatic discharge, fast transients from switching, surges, conducted RF, or radiated RF. | Reset-sensitive controllers, safety-related controls, low-level analog inputs, and communication ports. | Unexpected resets, false input transitions, corrupted data, or loss of communication occur during disturbances. | Review equipment documentation and applicable immunity requirements. Relevant IEC 61000-4 test methods include ESD (-4-2), electrical fast transient/burst (-4-4), and surge (-4-5). | Match protection to the disturbance and port: options may include suitable transient protection, filtering, shielding, or galvanic isolation. |
| 5. Inspect cable and port details | Common-mode currents on cable shields, poor connector termination, long unshielded pigtails, and cable-entry gaps. | Ethernet, fieldbus, encoder, thermocouple, and other low-level or high-speed signal interfaces. | Faults change when a cable is touched, replaced, rerouted, or connected to a different port. | Check cable type, connector pinout, shield continuity, termination method, and the installation guidance for both connected devices. | Use compatible cables and connectors; terminate shields and bond enclosures as specified by the equipment design and site grounding plan. |
| 6. Verify the installation environment | Shared trays, long parallel cable runs, poor equipotential bonding, and noisy power distribution. | Remote I/O, distributed sensors, control cabinets, and equipment connected across separate structures or panels. | Intermittent issues vary by route, shift, equipment configuration, or connection between cabinets. | Document cable routes, lengths, tray sharing, enclosure bonds, and supply connections. Compare affected and unaffected installations or routes. | Improve routing and separation, maintain low-impedance bonding, and follow the equipment manufacturer's installation instructions. |
| 7. Test the fix under real operating conditions | Combined disturbances from multiple sources, especially during startup, braking, switching, or high-load operation. | Any equipment that must remain reliable during normal production and foreseeable electrical disturbances. | A change appears to work at idle but faults return when multiple machines operate or production conditions change. | Repeat checks across operating modes, loads, and relevant cable configurations. Record symptoms, measurements, and test conditions before and after changes. | Choose a solution supported by measured evidence, then verify that it does not compromise safety, protective bonding, signal integrity, or applicable compliance requirements. |